Bike Cycling and Travel: How to Assemble a New Road Bike

Prepare Jobs

For this job you'll need a number of tools. Ideally you must have a repair work stand. Other necessary devices include cable cutters, a collection of metric allen secrets, a pedal wrench and an air pump.

Step 1

Cut the wire tires for the wheels. Note: Please take the wheel out of the crankset arm with treatment.

Cut the cable tie for the seatpost.

Action 2

Put the seatpost into the seat tube. Use 4mm Allen trick to tight the seat clamp.

Clamp the bike onto a bicycle fixing stand

Step 3

Usage 4 mm Allen key to eliminate the stem cap and place the handlebar right into the place

Use 4 mm Allen secret to limited the bolts. Keep in mind: 4 screws need to be evenly limited.

Change the handlebar to your favorite angle

Tip 4

Eliminate all protectors off the bike

Step 5

Area the rear brake wire housing into the cord holder on the frame

Pull the back brake wire Note: Please see to it the back brake cable television end in the best placement in the lever. Test it by applying brake bar.

Area the front brake cable television housing right into the brake calliper owner and also draw the brake cable television.

Step 6

Use some oil on the front wheel skewer

Inter the skewer into front wheel. Keep in mind: there are 2 springtimes one for right, the various other one for left

Please see the picture for spring position.

Step 7

Location the front wheel right into fork

Please make certain the wheel is the centre of the fork than close the fast launch lever to secure the wheel.

Tip 8 (Adjust the front brake).

Place the front brake cord owner on the calliper as the image.

Owner the brake calliper and draw the cable, then use 5mm Allen secret to protect the cable television once it gets to ideal setting.

Tight the screw to protect the brake cable.

Close the brake stress modification lever.

Adjust the brake pads elevation and also ensure the pads might be applied on the wheel's stopping surface. After that leave sensible added and also reduced the brake cable utilizing a wire cutter. Keep in mind: Please do not cut as well brief, you could require to re-assemble the brake cable television in the future.

Squeeze the cable television upright the brake cable.

Step 9( Rear Brake Change).

Put the back brake cord right into the holder (like front).

Change the brake pads height using 4mm Allen secret and also make sure the pads can be applied on the wheel's braking surface.

Press the cord end on the brake cord.

Leave a bit extra for future usage.

Step 10 (Pedals setting up).

Pedals have various thread. Examine the mark on the axle "L" indicates left pedal, "R" implies right pedal. Note: Drive side is right, non drive side is left. Use some oil on the pedal axle.

Transform the right pedal axle clockwise by hand.

Lock the axle making use of a 15mm pedal wrench. Keep in mind: Please do not scrape the painting of the crank arm. Reasonably tight, if too loose, the axle would certainly move after that potentially would harm the string of the crank arm. As well as service warranty will not cover that.

Left pedal mounting by turning the axle counter clockwise by hand.

Lock the axle using a 15mm pedal wrench.

Step 11( Readjust the rear derailleur).

To change the rear derailleur, it could be tough if you do not have the experience.

Cut the wire and leave a little bit extra. Squeeze the cable end on the wire.

Step 12.

Please see the video.

Change the alignment of the back derailleur (Please see the video.

Keep in mind: before you change cable televisions stress for the front and also rear derailleur, you require to apply shifter levers to see to it the cable televisions remain in loosened placement.

Tip 13.

5mm Allen secret to limited the top lock first. Note: please do not over limited, it may harm the bearing inside.

Readjust the handlebar angle alongside the front wheel as well as Tight the side bolts to lock the stem on the fork steerer.

Pump the tire utilizing suitable air pump for Presta (French Kind) shutoff. Note: You require to loosen the valve cap prior to you pump it.